RUCOAT® Eqaulizer
RuCoat® Equalizer is a specially formulated product designed to minimize surface texture and porosity differences between wallboard face paper and finished joints in new drywall construction. “Joint banding” and “photographing” are common problems that occur due to the differences in absorption rates between drywall face paper and joint compound. This is especially problematic when viewed in direct natural lighting conditions. Ordinary primers/sealers do not adequately address this situation either because they simply provide a film that covers the surface or they lack the necessary type and amount of pigments and/or fillers. RuCoat Equalizer solves this problem by equalizing the porosity of the wallboard face paper and joint compound, thus minimizing the surface texture differences. The result is a more uniform surface that dramatically improves the finish coat.
ADVANTAGES
Efficient:
Equalizes porosity differences for fewer decorating problems.
Consistent:
Minimizes surface texture variations. Fast Set: Dries to the touch in less than 30 minutes. Distinct Finish: Excellent wet and dry hide. Even Surface: Smooth, lump-free consistency. Flexible
Application:
Applies with roller, brush, airless, or conventional sprayer.
RUCO® Southern Wall Products Incorporated
Customer Service: 1-800-554-9255
1825 Fellowship Rd
Tucker, Georgia 30084
770-621-3065
Product Specifications and Details
Product Data
MATERIAL:
Non-asbestos, latex formulation
TYPE:
Spray machine or hand-roller application
PRODUCT SENSITIVITY:
Do not apply in temperature below 50°F or above 100°F.
Substrate must be thoroughly dry.
COVERAGE:
Up to 500 ft’ / gallon, depending on the film thickness and surface porosity.
STORAGE:
Store in enclosed dry storage area, both in the supplier’s warehouse and on the job site.
5.0 Gallon Pail
Architectural Specifications
PART 1: GENERAL
1.01 Scope Specify to meet project requirements.
1.02 Qualifications Southern Wall Products, Inc. and approved manufacturers shall manufacture all Gypsum Wallboard finishing materials. The materials shall be installed in accordance with the Association of Wall and Ceiling Industries’ “Recommended Levels of Gypsum Board Finish.”
1.03 Delivery and Storage Store in an enclosed shelter in the original unopened packages. Protect from temperatures below freezing and over 120°F.
1.04 Project Conditions
A. Install interior gypsum wallboard finishing materials only after the building is enclosed.
B. Ventilation:
- Provide ventilation during and following joint treatment application.
- Use temporary air circulators in enclosed areas lacking natural ventilation.
- Allow additional drying time between coats of joint treatment under slow drying conditions.
- Protect installed materials from drafts during hot, dry weather.
C. Temperature:
Maintain a minimum surface, mix, and air temperature of 50°F – 100°F until all joints have dried completely.
PART II: PRODUCTS
2.01 Materials
A. Joint Reinforcement – Ruco® Reinforcing Tapes
B. Joint Treatment
- Ruco® Ready Mixed Joint Compounds
- Ruco® Set Type Joint Compounds
C. Ceiling and Wall Texture – Ruco® Design Texture
D. Surface Equalizers
PART III: EXECUTION
3.01 Installation Use all products in accordance with Southern Wall Products’ printed package instructions.
3.02 Application – Joint Compound
(Each level and specific application to be determined in accordance with recommended Levels of Gypsum Board Finish as developed by AWCI)
A. Level 1 Intended for plenum areas above ceilings, areas where assembly is concealed by final construction, smoke barriers, and separation walls in attics.
B. Level 2 Intended for water-resistant gypsum board for tile substrate, garages, warehouses, and other areas where appearance is not of primary concern.
C. Level 3 Intended for appearance areas receiving heavy or medium texture finishes or where heavy grade wallcoverings are to be applied as final finish.
D. Level 4 Intended for appearance areas receiving flat paints, light texture finishes, or light or medium weight wallcovering.
E. Level 5 Intended for appearance areas receiving flat, low-luster, semi-gloss, gloss, or enamel finish paints or coatings, light texture finishes, light or medium weight wallcovering, un-backed vinyl wallcoverings, or severe light conditions.